Unbeatable Offer
Save 1%
-1%
LCR-T4 Diode Triode Capacitance Esr Meter Transistor
₨ 1,980.00-
Arduino, Arduino Boards & Components, Development Kits
0-60V Battery Level Meter
It is the perfect multifunctional tool for troubleshooting. Measure the power and energy consumption of any battery-powered device. The easy-to-read LCD screen provides clear digital readings. When connected, the wattmeter will continuously provide real-time readings of amperes, volts and watts. The device can calculate the voltage, current, power, discharge capacity and discharge time of the aircraft, and calculate the force effect of the multi-axis aircraft. Large screen reality, backlight can be set, function switching query.
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
MPU 6050 3 Axis Digital Gyroscope Accelerometer Sensor Module
-3%
Arduino, Arduino Boards & Components, Development KitsMPU 6050 3 Axis Digital Gyroscope Accelerometer Sensor Module
Key Features :
- Build in ultra low noise linear LDO voltage regulator
- Build-in on board filters, which reduce noise from motor and other high current electronics
- All sensors connected to I2C bus
- You can easily select two I2C address for MPU6050 by soldered jumper
- Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of ±250, ±500, ±1000, and ±2000dps
- Tri-Axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
- Digital Motion Processing™ (DMP™) engine offloads complex MotionFusion, sensor timing synchronization and gesture detection
- Embedded algorithms for run-time bias and compass calibration. No user intervention required
- Power LED
- Input Voltage: 2.3 – 3.4V
- Build in Logic level converter for I2C
- Digital-output temperature sensor
- Dimensions 20x16mm
- Designed for 5V logic level
SKU: n/a -
Automatic Voltage Regulators (AVRs)
DSR Mecc Alte Automatic Voltage Regulator AVR For Generator
Key Features
- Full digital controlled regulator, based on DSP
- On-board machine installation
- Suitable for all self-regulated alternators
- Voltage supply: 40Vac270Vac (from auxiliary winding, output voltage or PMG)
- Frequency range: 12Hz 72Hz
- Sensing of voltage with true RMS or average measurement (70280 Vac)
- Maximum continuous output current: 5Adc;
- Precision of voltage regulation: 1% from no-load to nominal load
- Click Here To Download DSR User Manual
SKU: n/a -
Automatic Voltage Regulators (AVRs)
AVR EA05 Generator Automatic Voltage Regulator
Key Features
- Sensing Input: Voltage 220 / 380 / 440 VAC, 1 phase2 wire DIP switch selectable
- Frequency: 50 / 60 Hz, DIP switch selectable
- Power Input Voltage: 100 ~ 300 VAC, 1 phase 2 wire
- Output Voltage: Max. 90 VDC @ 240 VAC input
- Current Continuous: 5A Intermittent 7A for 10 sec
- Resistance: Min. 15 ohm Max. 100 ohm
- Voltage Regulation: < 0.5% ( with 4% engine governing )
- Voltage Build-up: Residual voltage at AVR terminal > 5 VAC
- Thermal Drift: 0.03% per C change in AVR ambient
- Click Here To Download EA05 User Manual
SKU: n/a -
Control Card, Full Color Controllers, SMD Screens & Tickers
HD-U60-75 Full Color LED Control Card with USB Port
-13%
Control Card, Full Color Controllers, SMD Screens & TickersHD-U60-75 Full Color LED Control Card with USB Port
Key Features
- Support module: Used indoor outdoor, semi-outdoor full color display
- Control range: Full color: 640W*64H
- FLASH Capacity: 8M Byte
- Communication Port: U-Disk
- HUB signal: 2 HUB75
- Program Quantity: 1000pcs Programs. also can change program by button or remote if weld sensor (Remoter can select 1-999 Programs)
- Area Quantity: 20 areas with separate zone, and separated special effects and border
- Display Showing: TextAnimation wordTimeCountLunar calendar Display effects
- Click Here to Download HD-U60-75 User Manual
- Click Here to Download HD-U60-75 Software HD2018
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Nodemcu Mini ESP8266 Wemos D1-Mini Wifi
Key Features :
-
-
- 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire
- supported(except D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Use BRT (Bias Resistor Transistor), easier into flash mode.
- 30% increase in radiating area, more stable.
- Dimensions : 35 x 26 x 8 (LxWxH) mm.
- Weight: 10 gm.
- Board Color : Blue
- Compatible with Arduino
- Compatible with NodeMCU
- Compatible with MicroPython
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
SR04T Waterproof Ultrasonic Sensor Jsn-sr04t Distance
-1%
Arduino, Arduino Boards & Components, Development KitsSR04T Waterproof Ultrasonic Sensor Jsn-sr04t Distance
Key Features :
-
- small size, easy to use;
- low voltage, low power consumption;
- high accuracy;
- strong anti-jamming;
- integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions.
SKU: n/a -
-
Single/Full Color (RGB) Panels/Modules, SMD Screens & Tickers
Red P10 Single Color Outdoor SMD Module For Tickers
-10%
Single/Full Color (RGB) Panels/Modules, SMD Screens & TickersRed P10 Single Color Outdoor SMD Module For Tickers
Key Features
- Red P10 Single Color SMD Module For Tickers
- Full outdoor: IP64
- Size (W x H): 320 x 160 mm (320 x 160cm), 12.6 x 6.3 Inch
- Resolution (W x H): 32 x 16 = 512
- HUB Signal: HUB12
- Volt: 5v DC
- Brightness: 4500 cdm (nits)
- LED: DIP 5mm
- Accessories: Data Wire, Power Cable, 4-Magnets
- Can work with control card: U6A, U6B, U60, W60, U61, U62, U64, U6BN, WLP-XUA2, WLP-XUB1, etc.
- The display can Show: Text, Animation word, Time, Count, Lunar calendar
- Support simple animation characters
- Click Here to Download HD-U6A Software HD2018
SKU: n/a
-
Arduino, Arduino Boards & Components, Development Kits
Arduino Uno R3 SMD with USB Cable
Key Features
- The operating voltage is 5V
- The recommended input voltage will range from 7v to 12V
- The input voltage ranges from 6v to 20V
- Digital input/output pins are 14
- Analog i/p pins are 6
- DC Current for each input/output pin is 40 mA
- DC Current for 3.3V Pin is 50 mA
- Flash Memory is 32 KB
- SRAM is 2 KB
- EEPROM is 1 KB
- CLK Speed is 16 MHz
- Click Here to Download Open Source Arduino Software
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Arduino Nano
Key Features
- MICROCONTROLLER: ATmega328
- ARCHITECTURE: AVR
- OPERATING VOLTAGE: 5 V
- FLASH MEMORY: 32 KB of which 2 KB used by bootloader
- SRAM: 2 KB
- CLOCK SPEED: 16 MHz
- ANALOG IN PINS: 8
- EEPROM: 1 KB
- DC CURRENT PER I/O PINS: 40 mA (I/O Pins)
- INPUT VOLTAGE: 7-12 V
- DIGITAL I/O PINS: 22 (6 of which are PWM)
- PWM OUTPUT: 6
- POWER CONSUMPTION: 19 mA
- PCB SIZE: 18 x 45 mm
- WEIGHT: 7 g
- Click Here to Download Open Source Arduino Software
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Arduino Pro Mini 5V 16MHz
Key Features
- Microcontroller: ATmega328
- Board Power Supply: 5 – 12 V (5V model)
- Circuit Operating Voltage: 5V
- Digital I/O Pins: 14
- PWM Pins: 6
- UART: 1
- SPI: 1
- I2C: 1
- Analog Input Pins: 6
- External Interrupts: 2
- DC Current per I/O Pin: 40 mA
- Flash Memory: 32KB of which 2 KB used by bootloader
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock Speed: 16 MHz
- Click Here to Download Open Source Arduino Software
SKU: n/a -
Automatic Voltage Regulators (AVRs)
AVR MX321 Automatic Voltage Regulator with Hard Shell for Stamford Generator
Automatic Voltage Regulators (AVRs)AVR MX321 Automatic Voltage Regulator with Hard Shell for Stamford Generator
- MX321 AVR adjustment rate is better than 0.5%
- High-quality generator voltage regulator
- Long service life
- Built-in low-speed protection
- Over excitation protection
- Over-voltage protection
- Over-current protection
- LAM Protection
- Professional manufacturing
- Exquisite workmanship
- High reliability
- High-quality capacitor and terminal
- Superior performance
- Click Here To Download MX321 User Manual
SKU: n/a -
Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start Units
EPH-106 AMF Auto Mains Failure Card For Generator
-25%
Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start UnitsEPH-106 AMF Auto Mains Failure Card For Generator
Key Features
- Microprocessor controlled
- No need to put any extra timer
- Automatic fuel control and start
- Automatic shutdown on fault condition
- LEDs for fault monitoring
- Screw type connectors for easy connections
- Survive cranking drop-outs
- Small size
- Manual fuel control and start
- Low cost
- Adjustable self-time
- Low failure rate
SKU: n/a -
Generator Battery Chargers
SMPS125 12V/5A Battery Charger for Generators
Key Features
- 100 KHz switchmode architecture
- Float charging system
- Constant voltage output
- Current limited
- Rugged design for industrial environments
- Wide operating voltage range
- Rectifier fail output
- Boost charge input
- Short circuit protection
- Overload protection
- High-temperature protection
- Plug-in connection system
- Click Here To Download SMPS125 User Manual
SKU: n/a -
Genset Products, Synchronization Units
DSE8610-MKII Synchronization Controller
Key Features
- Multi Genset synch & load share
- AMF unit (uninterrupted transfer)
- ATS unit (uninterrupted transfer)
- Remote start controller
- Manual start controller
- Engine controller
- Remote display panel
- Comprehensive synchronizing & load sharingcapabilities
- Built-in governor and AVR control
- Baseload (kW export) control
- Positive & negative kVAr export control
- Mains (Utility) decoupling protection
- 4-Line backlit LCD text display
- CAN AVR support
- Click Here To Download DSE8510-MKII User Manual
- Click Here To Download DSE8610-MKII Config. Suite PC Software Manual
SKU: DSE8610-MKII -
Genset Products, Synchronization Units
D700 Advanced Auto-Learning Genset Synchronization Controller
-7%
Genset Products, Synchronization UnitsD700 Advanced Auto-Learning Genset Synchronization Controller
D700 synchronization controller is tailored for the most demanding applications, and it can be used for
- Multi Genset synch & load share
- Mains synchronization
- Single Genset parallel with mains
- AMF unit (uninterrupted transfer)
- ATS unit (uninterrupted transfer)
- Remote start controller
- Manual start controller
- Engine controller
- Remote display panel
- Long term data record on a flash drive
- On-board Input&output extension
- Comprehensive synchronizing & load sharingcapabilities
- Built-in governor and AVR control
- Baseload (kW export) control
- Positive & negative kVAr export control
- Mains (Utility) decoupling protection
- 4-Line backlit LCD text display
- CAN AVR support
- Click Here To Download D700 User Manual
SKU: D700-Synch-TFT-Version
-
Genset Products, Manual & Remote Start Units
DSE3110 Manual & Auto Genset Controller
Key Features
- Back-lit icon LCD display
- Front panel editing
- LED and LCD alarm indication
- Power Save mode
- PC configurable
- 6 Digital inputs
- 4 Outputs (2 configurable)
- Configurable timers and alarms
- Remote Start input
- Generator voltage display
- Generator frequency display
- Battery voltage display
- Engine speed display
- Hours counter
- Engine pre-heat
- Click Here To Download DSE3110 User Manual
- Click Here To Download DSE3110 Data Sheet
SKU: n/a -
Genset Products, Synchronization Units
DSE8610-MKII Synchronization Controller
Key Features
- Multi Genset synch & load share
- AMF unit (uninterrupted transfer)
- ATS unit (uninterrupted transfer)
- Remote start controller
- Manual start controller
- Engine controller
- Remote display panel
- Comprehensive synchronizing & load sharingcapabilities
- Built-in governor and AVR control
- Baseload (kW export) control
- Positive & negative kVAr export control
- Mains (Utility) decoupling protection
- 4-Line backlit LCD text display
- CAN AVR support
- Click Here To Download DSE8510-MKII User Manual
- Click Here To Download DSE8610-MKII Config. Suite PC Software Manual
SKU: DSE8610-MKII -
Genset Products, Manual & Remote Start Units
DSE4510-MKII-CHN Manual & Auto Genset Controller
Key Features
- Alternator frequency & CAN speed sensing in one variant
- Largest back-lit icon display in its class
- Heated display option
- Real-time clock provides accurate event logging
- Fully configurable via the fascia or PC using USB communication
- Extremely efficient power save mode
- 3 phase generator sensing
- Compatible with 600 V ph to ph nominal systems
- Generator/load power monitoring (kW, kV A, kV Ar, pf)
- Accumulated power monitoring (kW h, kVA h, kVAr h)
- Generator overload protection (kW)
- Generator/load current monitoring and protection
- Fuel and start outputs (configurable when using CAN)
- 2 configurable DC outputs
- 3 configurable analog/digital inputs
- 4 configurable digital inputs
- Configurable staged loading outputs
- 3 engine maintenance alarms
- Engine speed protection
- Engine hours counter
- Engine pre-heat
- Engine run-time scheduler
- Engine idle control for starting & stopping
- Battery voltage monitoring
- Start on low battery voltage
- Configurable remote start input
- 1 alternative configuration
- Comprehensive warning, electrical trip or shutdown protection upon a fault condition
- LCD alarm indication
- Event log (50)
- Click Here To Download DSE4510 User Manual
- Click Here To Download DSE4510 Data Sheet
SKU: n/a -
Automatic Mains Failure Units (AMF), Genset Products
DSE4520-MKII Auto Mains (Utility) Failure Genset Controller
-20%
Automatic Mains Failure Units (AMF), Genset ProductsDSE4520-MKII Auto Mains (Utility) Failure Genset Controller
Key Features
- Alternator frequency & CAN speed sensing in one variant
- Largest back-lit icon display in its class
- Heated display option
- Real-time clock provides accurate event logging
- Fully configurable via the fascia or PC using USB communication
- Extremely efficient power save mode
- 3 phase generator sensing
- Compatible with 600 V ph to ph nominal systems
- Generator/load power monitoring (kW, kV A, kV Ar, pf)
- Accumulated power monitoring (kW h, kVA h, kVAr h)
- Generator overload protection (kW)
- Generator/load current monitoring and protection
- Fuel and start outputs (configurable when using CAN)
- 4 configurable DC outputs
- 3 configurable analog/digital inputs
- 4 configurable digital inputs
- Configurable staged loading outputs
- 3 engine maintenance alarms
- Engine speed protection
- Engine hours counter
- Engine pre-heat
- Engine run-time scheduler
- Engine idle control for starting & stopping
- Battery voltage monitoring
- Start on low battery voltage
- Configurable remote start input
- 1 alternative configuration
- Comprehensive warning, electrical trip or shutdown protection upon a fault condition
- LCD alarm indication
- Event log (50)
- Click Here To Download DSE4520 User Manual
- Click Here To Download DSE4520 Data Sheet
SKU: n/a -
Genset Products, Manual & Remote Start Units
GTR-168 Manual & Auto Genset Controller With Key Switch
-17%
Genset Products, Manual & Remote Start UnitsGTR-168 Manual & Auto Genset Controller With Key Switch
Key Features
- Automatic/Manual engine starting and stopping
- Gas engine support
- Emergency / Auxiliary engine shutdown
- Low battery warning
- Over speed shutdown
- High water temperature shutdown
- Low oil pressure shutdown
- Survives cranking dropouts
- Key switch to avoid unauthorized access
- ATS Auto Start function by detecting ATS terminal 12 grounded
- Plug-in connection system for easy replacement
- Low cost
- Small dimensions
- Standard panel dimensions, (72x72mm)
- Click Here To Download GTR-168 User Manual
SKU: n/a -
Genset Products, Manual & Remote Start Units
DKG155 Manual Start Genset Controller With Key Switch
-35%
Genset Products, Manual & Remote Start UnitsDKG155 Manual Start Genset Controller With Key Switch
Key Features
- Microprocessor controlled
- Manual fuel control and start
- Automatic shutdown on fault condition
- Survives cranking dropouts
- Digital display of generator frequency
- High engine temperature protection
- Low oil pressure protection
- Overspeed-under speed protection
- Spare fault input
- Alarm output
- Two-part connectors for easy replacement
- Standard panel dimensions (72x72mm)
- Low cost
- Low failure rate
- Click Here To Download DKG155 User Manual
- Click Here To Download DKG155 Brochure
SKU: n/a -
Genset Products, Manual & Remote Start Units
DSE501K Manual Start Genset Controller With Key Switch
-24%
Genset Products, Manual & Remote Start UnitsDSE501K Manual Start Genset Controller With Key Switch
Key Features
- Microprocessor controlled
- Manual fuel control and start
- Automatic shutdown on fault condition
- Survives cranking dropouts
- High engine temperature protection
- Low oil pressure protection
- Overspeed-under speed protection
- Alarm output
- Plug-in connectors for easy replacement
- Standard panel dimensions (72x72mm)
- Low cost
- Low failure rate
- Click Here To Download DSE501K Manual
SKU: n/a -
Genset Products, Manual & Remote Start Units
DSE701 Manual & Auto Start Genset Controller With Key Switch
-18%
Genset Products, Manual & Remote Start UnitsDSE701 Manual & Auto Start Genset Controller With Key Switch
Key Features
- Microprocessor controlled
- Manual fuel control and start
- Automatic shutdown on fault condition
- Survives cranking dropouts
- High engine temperature protection
- Low oil pressure protection
- Overspeed-under speed protection
- Two-part connectors for easy replacement
- Standard panel dimensions (72x72mm)
- Low cost
- Low failure rate
- Click Here To Download DSE701 User Manual
SKU: n/a
Products Grid
Crazy Discounts
Best Sellers
-
Genset Products, Manual & Remote Start UnitsDSE3110 Manual & Auto Genset Controller
₨ 18,500.00₨ 22,000.00 -
Automatic Mains Failure Units (AMF), Genset ProductsDKG307 Automatic Mains Failure Unit
₨ 190,000.00₨ 220,000.00 -
Genset Products, Synchronization Units
D700 Advanced Auto-Learning Genset Synchronization Controller
₨ 350,000.00₨ 375,000.00
-
Genset Products, Manual & Remote Start UnitsDKG116 Manual And Remote Start Unit
₨ 14,500.00₨ 15,000.00 -
Genset Products, Synchronization UnitsDKG117 Synchroscope And Check Synch Relay
₨ 15,000.00₨ 16,500.00 -
-
Genset Products, Manual & Remote Start UnitsDKG215 Manual And Remote Start Unit
₨ 22,000.00₨ 25,000.00 -
Automatic Mains Failure Units (AMF), Genset ProductsDKG309 Automatic Mains Failure Unit
₨ 48,000.00₨ 55,000.00
-
Genset Products, Manual & Remote Start UnitsDKG317 Manual And Remote Start Unit
₨ 27,000.00₨ 30,000.00 -
Auto Transfer Switches (ATS), Genset ProductsDKG325 Genset Control & ATS Panel
₨ 35,000.00₨ 40,000.00 -
Automatic Mains Failure Units (AMF), Genset ProductsDKG509 Automatic Mains Failure Unit
₨ 68,000.00₨ 70,000.00 -
Automatic Mains Failure Units (AMF), Genset ProductsDKG507 Automatic Mains Failure Unit
₨ 58,000.00₨ 65,000.00
Recently Added
Arduino, Arduino Boards & Components, Development Kits
MB-102 Breadboard 830 Points Solderless Prototyping Breadboard
-3%
Arduino, Arduino Boards & Components, Development Kits
MB-102 Breadboard 830 Points Solderless Prototyping Breadboard
Key Features :
Mb102 Bread Board
830 Solder-less Points
Ideal for Experimenting With Circuit Design In Labs
Compatible with resistance, diodes, transistors, LED’s , Capacitors and other types of electronic components
Completely reusable
Colored coordinates for easy components placement.
Phosphor bronze nickel plated spring clips.
Accept a variety of wire sizes 20-29 AWG
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
I2C PCF8574 IIC I2c Serial Interface Adapter Module Iic I2C LCD Module
-3%
Arduino, Arduino Boards & Components, Development Kits
I2C PCF8574 IIC I2c Serial Interface Adapter Module Iic I2C LCD Module
Key Features :
5V power supply.
Serial I2C control of LCD display using PCF8574.
The backlight can be enabled or disabled via a jumper on the board.
Contrast control via a potentiometer.
Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Size ：41.6 x 19.2 mm.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
FireFlame Sensor
Key Features :
Product Name: Flame Sensor Module
Output Channel: 1
Power Supply: 3.3/5V
PCB Board Size: 32 x 14mm(L*W)
Hole Size: 3mm
Material: Electric Part
Net Weight 3g
indicator light: a green one for the switch, a red one for power.
Built in a potentiometer for sensitivity control.
Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO.
Can detect fire or wavelength in 760 ~ 1100 nm nano within the scope of the light source.
Detection angle about 60 degrees, the flame spectrum especially sensitive.
The flame of the most sensitive sensors flame, the regular light is also a response, generally used for fire alarm purposes.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
Water Level Sensor
Key Features :
Operating voltage: DC3-5V
Operating current: less than 20mA
Sensor Type: Analog
Detection Area: 40mmx16mm
Production process: FR4 double-sided HASL
Operating temperature: 10℃-30℃ Humidity: 10% -90% non-condensing
Dimensions: 60mmx20mm
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
DS3231 (Precision Rtc Real Time Clock Module With Cell)
-2%
Arduino, Arduino Boards & Components, Development Kits
DS3231 (Precision Rtc Real Time Clock Module With Cell)
Key Features :
DS3231 based RTC with 2032 Battery Holder.
Highly Accurate RTC Completely Manages All Timekeeping Functions.
Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year, with Leap-Year Compensation Valid Up to 2100.
Digital Temp Sensor Output.
Register for Aging Trim.
Configurable I2C device Address for AT24C32 using SMD jumpers on PCB (A0, A1, A2).
Two Time-of-Day Alarms.
Programmable Square-Wave Output Signal.
Battery-Backup Input for Continuous Timekeeping.
Low Power Operation Extends Battery-Backup Run Time.
3.3V Operation.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
Voltage Sensor Dc 0 To 25v Voltage Sensor
Key Features :
Dimensions: 28 x 14 x 13 mm(LxWxH).
Weight: 4 gm.
Input Voltage range: DC0 to 25 V
Voltage detection range: DC 0.02445 V to 25 V
Analog Voltage resolution : 0.00489 V
Output Interface : “+ ” connected 5/3.3V, “-” connected GND, “s” connected Arduino AD pins
DC input interface: red terminal positive with VCC, negative with GND
You can also use the IICLCD1602 LCD to display voltage.
By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
TTP 223 Touch Sensor Module Touch Sensor
Key Features :
Modes Toggle or switch.
Operating current @VDD=3V, no-load, SLRFTB=1.
The response time max about 60mS at fast mode, 220mS at low power mode @VDD=3V.
Sensitivity can adjust by the capacitance(0~50pF) outside.
Have two kinds of sampling length by pad option(SLRFTB pin).
Stable touching detection of the human body for replacing traditional direct switch key.
Provides Fast mode and Low Power mode selection by pad option(LPMB pin).
Provides direct mode toggle mode by pad option(TOG pin), the open-drain mode by bonding option, OPDO pin is an open-drain output, Q pin is CMOS output.
All output modes can be selected active high or active low by pad option(AHLB pin).
Have the maximum on-time 100sec by pad option(MOTB pin).
Have external power-on reset pin(RST pin).
After power-on have about 0.5sec stable-time, during the time do not touch the keypad, And the function is disabled.
Auto calibration for life.
Re-calibration period is about 4.0sec when the key has not to be touched.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
Max232 Rs232 To Ttl Converter Module Db9 Serial Port Connector
-3%
Arduino, Arduino Boards & Components, Development Kits
Max232 Rs232 To Ttl Converter Module Db9 Serial Port Connector
Key Features :
It is widely used in radio modification, phone flash, XBOX360 flash, GPS, vehicle detection, DVD flash, hard disk repair set-top box upgrade.
It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU
Pre-assembled compact size board
Suitable for use with most microcontrollers
Operates up to 250 kbit/s
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
SR04T Waterproof Ultrasonic Sensor Jsn-sr04t Distance
-1%
Arduino, Arduino Boards & Components, Development Kits
SR04T Waterproof Ultrasonic Sensor Jsn-sr04t Distance
Key Features :
small size, easy to use;
low voltage, low power consumption;
high accuracy;
strong anti-jamming;
integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
DS1302 (Real Time Clock Ds1307 Ds 1307 Rtc I2c Module At24c32)
-3%
Arduino, Arduino Boards & Components, Development Kits
DS1302 (Real Time Clock Ds1307 Ds 1307 Rtc I2c Module At24c32)
Key Features :
Two-wire I2C interface
Hour: Minutes: Seconds AM/PM
Leap year compensation
Accurate calendar up to the year 2100
Consumes Less than 500nA in Battery-Backup
1Hz output pin
56 Bytes of Non-volatile memory available to the user
4KB of serial electrically erasable and programmable read-only memory (EEPROM)
Embed DS18B20 temperature sensor interface with the pull-up resistor.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
KY-012 Small Active Buzzer Diy Module
Key Features :
Small and compact size, making it easy to integrate into your project
Produces a loud and clear sound that can be heard from a distance
Can be easily controlled with a microcontroller or other digital circuit
Low power consumption, making it suitable for battery-powered projects
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
ADXL-1345 Tripple Axis Accelerometer Module
-3%
Arduino, Arduino Boards & Components, Development Kits
ADXL-1345 Tripple Axis Accelerometer Module
Key Features :
Voltage – Supply : 3.3 V/ 5V.
Interface : I²C, SPI.
Sensing Range : ±2g, 4g, 8g, 16g.
Sensitivity:
X : 28.6 LSB/g.
Y : 31.2 LSB/g.
Z : 34.5 LSB/g.
Sensor Type : Accelerometer 3 Axis.
Dimensions : 28 mm x 14 mm.
Weight : 10 gm.
Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V.
Free-Fall Detection.
Tap/Double Tap Detection.
Flexible interrupt modes mappable to either interrupt pin Measurement ranges selectable via serial command Bandwidth selectable via serial command
Wide temperature range (−40°C to +85°C).
10,000 g shock survival.
Support 5V/3.3V voltage input, on-board RT9161 power chip, lower pressure drop faster than the 1117, faster load speed of response, very suitable for high-noise power supply environment.
User-selectable resolution
Fixed 10-bit resolution.
Full resolution, where resolution increases with g range, up to 13-bit resolution at ±16 g (maintaining 4 mg/LSB scale factor in all g ranges).
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
Water Flow Sensor
Key Features :
Model: YF-S201
Sensor Type: Hall effect
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
Max current draw: 15mA @ 5V
Output Type: 5V TTL
Working Flow Rate: 1 to 30 Liters/Minute
Working Temperature range: -25 to +80℃
Working Humidity Range: 35%-80% RH
Accuracy: ±10%
Maximum water pressure: 2.0 MPa
Output duty cycle: 50% +-10%
Output rise time: 0.04us
Output fall time: 0.18us
Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
Pulses per Liter: 450
Durability: minimum 300,000 cycles
Cable length: 15cm
1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
Size: 2.5″ x 1.4″ x 1.4″
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
4×4 Keypad Matrix Keypad
Key Features :
Ultra-thin design & adhesive backing provides easy integration to any project
Excellent price-performance ratio
Easy communication with any microcontroller
5 pins 2.54mm pitch connector, 4x 4type 16 keys.
Sticker can peel off for adhesive mounting.
Used widely in industrial and home electronic equipments, instrument, etc.
This allows a microcontroller to ‘scan’ the 8 output pins to see which of the 16 buttons is being pressed.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
DC Volt Meter 3 wire DC 4.5 to 30V DC Red LED digital voltmeter module panel meter
-2%
Arduino, Arduino Boards & Components, Development Kits
DC Volt Meter 3 wire DC 4.5 to 30V DC Red LED digital voltmeter module panel meter
Key Features :
3 wire 0-100V Red LED digital voltmeter module panel meter
Sensing Voltmeter: 0-100V.
Power supply: DC4-30V
Measuring range: 0-100V.
Measurement accuracy: ±0.1%
Refresh rate: about 200ms
Display: 0.56 “digital tube
Color: Red
Operating current: Less than 8mA
Operating temperature: -10°C to 65°C
Input impedance:100K
Overall dimension: 48*29*26mm
Display LED color – Red
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
MPU 6050 3 Axis Digital Gyroscope Accelerometer Sensor Module
-3%
Arduino, Arduino Boards & Components, Development Kits
MPU 6050 3 Axis Digital Gyroscope Accelerometer Sensor Module
Key Features :
Build in ultra low noise linear LDO voltage regulator
Build-in on board filters, which reduce noise from motor and other high current electronics
All sensors connected to I2C bus
You can easily select two I2C address for MPU6050 by soldered jumper
Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of ±250, ±500, ±1000, and ±2000dps
Tri-Axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
Digital Motion Processing™ (DMP™) engine offloads complex MotionFusion, sensor timing synchronization and gesture detection
Embedded algorithms for run-time bias and compass calibration. No user intervention required
Power LED
Input Voltage: 2.3 – 3.4V
Build in Logic level converter for I2C
Digital-output temperature sensor
Dimensions 20x16mm
Designed for 5V logic level
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
Active Low Level Trigger Buzzer Alarm Module
-6%
Arduino, Arduino Boards & Components, Development Kits
Active Low Level Trigger Buzzer Alarm Module
Key Features :
Product Name:3.3 to 5V Active Buzzer Alarm Module Sensor And 3 Pin TTL Cable
The Transistor drive module uses 8550
With fixed bolt hole- easy installation- 2.6mm aperture.
Operating voltage 3.3V-5V
PCB dimensions: 34.28 mm (L) * 13.29 mm (W) * 11.5 mm (H)
Wire length: 20.5cm
Weight: 7 gm.
SKU: n/a
Arduino, Arduino Boards & Components, Development Kits
Micro SD TF Card Reader Adapter Module for Arduino
-3%
Arduino, Arduino Boards & Components, Development Kits
Micro SD TF Card Reader Adapter Module for Arduino
Key Features :
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board
Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm
Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Size: 45 x 28mm
Net weight: 6g
SKU: n/a