Welcome to Tetralink Technologies
Sale!

DKG217 Manual And Remote Start Unit With Synchroscope And Check Sync Relay

17,500

Key Features

  • Manual starting and stopping
  • Zero power consumption at rest
  • Remote Start operation available
  • LED bar graph synchroscope
  • Programmable ΔV, Δf, Δθ for check synch relay
  • Engine control
  • Generator protection
  • Built-in alarms and warnings
  • 3 phase Genset voltage inputs
  • 1 phase Genset CT input
  • 1 phase busbar voltage input
  • Engine oil pressure measurement
  • Engine coolant temperature measurement
  • Genset active power measurement (single phase)
  • Genset power factor measurement (single phase)
  • Periodic maintenance request indicator
  • Engine hours run counter
  • Plug-in connection system for easy replacement
  • Small dimensions (130x100x39mm)
  • Low cost
  • Click Here To Download DKG217 User Manual

Buy all Datakom products like generator controllers, energy meters,  panel meters,  synchronization controllers, auto mains failures (AMF), auto transfer switches (ATS), generator battery chargers, etc, online in Pakistan. You can buy DKG217 manual and remote start unit with synchroscope and check sync relay online or by visiting Electronic Power House (EPH) and Tetralink Technologies (TLT) in Lahore who are the authorized distributor of Datakom in Pakistan. All original Datakom products are available at very reasonable and best prices in Pakistan.

Features

  • Manual starting and stopping
  • Zero power consumption at rest
  • Remote Start operation available
  • LED bar graph synchroscope
  • Programmable ΔV, Δf, Δθ for check synch relay
  • Engine control
  • Generator protection
  • Built-in alarms and warnings
  • 3 phase Genset voltage inputs
  • 1 phase Genset CT input
  • 1 phase busbar voltage input
  • Engine oil pressure measurement
  • Engine coolant temperature measurement
  • Genset active power measurement (single phase)
  • Genset power factor measurement (single phase)
  • Periodic maintenance request indicator
  • Engine hours run counter
  • Event logging
  • Statistical counters
  • Front panel configurable
  • 100+ adjustable parameters
  • Logic level serial port
  • Optional RS-232 adapter
  • Free MS-Windows Remote monitoring SW:
    -local, LAN, IP and modem connection
    -monitoring, download of parameters
  • LED displays
  • Configurable analog inputs: 2
  • Configurable digital inputs: 5
  • Configurable relay outputs: 2
  • Total relay outputs: 5
  • Survives cranking dropouts
  • Sealed front panel
  • Plug-in connection system for easy replacement
  • Small dimensions (130x100x39mm)
  • Low cost

Description

The DKG-217 is an innovative generator control unit integrating 4 different functions needed for manually synchronized parallel gensets in a zero power consumption at rest structure. Integrated functions are:
– a manual start unit with power metering
– a remote start unit
– a led bar graph synchroscope
– a configurable check synch relay
The DKG-217 is designed to operate both manually and remotely. The manual control is made using the pushbuttons on the front panel. The remote control is made via the REMOTE START input signal.
The RUN and STOP pushbuttons select the operating mode. Other buttons select the display parameter scroll, alarm mute and lamp test functions. The unit has 4 different operation modes:
– power off (no current drain from the battery)
– power on (Genset stopped)
– genset running (synchronization not checked)
– synchronization checking
Each depression of the RUN button causes the unit to switch to next operation mode listed above. Each depression of the STOP button causes a return to the previous operation mode.
The REMOTE START signal causes the unit to switch between the first and the last operation modes. The synchronization checking consists of the verification of below conditions during 4 consecutive busbar cycles:
– the busbar voltage between set limits
– genset phase voltages between set limits
– busbar-Genset frequency difference below the set limit
– busbar-Genset voltage difference below the set limit
– busbar-Genset phase angle below the set limit
If all the above conditions are satisfied for 4 consecutive busbar cycles then the CHECK SYNCH relay will be immediately energized. If the busbar is not powered up, the synch checking may be overridden with the DEAD BUS ENABLE signal input. In Genset running and synchronization checking modes, the DKG-217 controls the automatic starting and stopping of the generating set. Once the generator is running, it monitors internal protections and external fault inputs. If a fault condition occurs, the unit shuts down the engine automatically and indicates the failure source with the corresponding red led
lamp.
The DKG-217 provides a comprehensive set of digitally
adjustable timers, threshold levels, input and output
configurations and operating sequences. The unauthorized
access to program parameters is prevented by the program lock
input. All programs may be modified via front panel pushbuttons,
and do not require an external unit.

Click Here To Download DKG217 User Manual

brands

DATAKOM

Color

Black

Reviews

There are no reviews yet.

Be the first to review “DKG217 Manual And Remote Start Unit With Synchroscope And Check Sync Relay”

Your email address will not be published. Required fields are marked *

You may also like…

  • Sale!

    DKG307 Automatic Mains Failure Unit

    22,500

    Key Features

    • True RMS measurementss
    • ECU connection through J1939 CAN option -for CAN version Only
    • MPU input option for MPU Version Only
    • Dual genset mutual standby operation
    • Event logging with time stamp and measurements
    • Battery backed-up real-time clock
    • Built-in daily/weekly / monthly exerciser
    • Weekly operation schedule programs
    • Field adjustable parameters
    • RS-232 serial port
    • Free MS-Windows Remote monitoring SW
    • Customer logo display capability
    • 10ADC relay outputs
    • Configurable analog inputs: 4
    • Configurable digital inputs: 7
    • Configurable relay outputs: 2
    • Total relay outputs: 6
    • I/O expansion capability
    • Plug-in connection system
    • Click Here To Download DKG307 User Manual
    Add to cart
  • Sale!

    DKG207 Automatic Mains Failure And Remote Start Unit

    15,500

    Key Features

    • Automatic mains failure
    • Engine control
    • Gas engine support
    • Generator protection
    • Built-in alarms and warnings
    • 3 phase mains voltage inputs
    • 1 phase Genset voltage input
    • 1 phase Genset CT input
    • Engine oil pressure measurement
    • Engine coolant temperature measurement
    • Genset active power measurement
    • Genset power factor measurement
    • Periodic maintenance request indicator
    • Engine hours counter
    • Statistical counters
    • Remote Start operation available
    • Survives cranking dropouts
    • Plug-in connection system for easy replacement
    • Small dimensions (130x100x39mm)
    • Low cost
    • Click Here To Download DKG207 User Manual
    Add to cart
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Compare
Wishlist 0
Open wishlist page Continue shopping